99 engines......

Just left the Post office, mailed 3 packages to WingingIt74, Micro and Mitchg 95. The cost of each was 3.50
I tried to get cost to ship to UK, 1st class under 4 lbs is about 10 to 13 dollars, over 4 lbs is more but not much more.
I will have to box them and take to PO to know exactly how much to UK. You folks overseas can tell me what you want,
I will box and ship and you can pay after I get an exact cost.

crankbndr wrote:Just left the Post office, mailed 3 packages to WingingIt74, Micro and Mitchg 95. The cost of each was 3.50
I tried to get cost to ship to UK, 1st class under 4 lbs is about 10 to 13 dollars, over 4 lbs is more but not much more.
I will have to box them and take to PO to know exactly how much to UK. You folks overseas can tell me what you want,
I will box and ship and you can pay after I get an exact cost.

thanks man, ill have to buy 3 more engines from you sometime sooon

Going through this box of engines I found a few are unrun and new inside. I disassembled them and cleaned the
crankcase bore and oil channel, lightly polished the crank. Cleaned old oil from cylinder and piston, the head
needed no work at all. I did not use Cox wrench on the exhaust ports of the #1 cylinder. I'd like to sell for 24$
per engine shipped to US.

crankbndr wrote:Going through this box of engines I found a few are unrun and new inside. I disassembled them and cleaned the
crankcase bore and oil channel, lightly polished the crank. Cleaned old oil from cylinder and piston, the head
needed no work at all. I did not use Cox wrench on the exhaust ports of the #1 cylinder. I'd like to sell for 24$
shipped to US.

i am interested in one of these that are cleaned up that well

crankbndr wrote:Well the engines arrived today, packed well not, that box must have weighted 40 lbs.
The engines that have needles now have bent needles. Now the good news, I was looking for
single port cylinders with a 1 fin car head, all these are stamped #1 two port cylinders with SPI and a standard
glowplug. Most have been run but they are not rusty, the castor did its job. They are a bear to take apart, the
cylinders have no cutout for a wrench, however I found the heat sink makes a nice removal tool.
This is what they look like

holy shnikeys man, i have to get one or two off ya

Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude wrote:Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude: is that just your favorite quote or are you interested in enya engines as well? quiet, so no one hears us talk. LOL

happydad

happydad wrote:

microflitedude wrote:Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude: is that just your favorite quote or are you interested in enya engines as well? quiet, so no one hears us talk. LOL

happydad

Don't worry, a lot of us here collect, use and fly MANY other makes of engine besides Cox, see some of my other posts in "Off Topic" to see how wide MY interests are! (Yes, I have Enyas too!)

Wilf

happydad wrote:

microflitedude wrote:Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude: is that just your favorite quote or are you interested in enya engines as well? quiet, so no one hears us talk. LOL

happydad

Pun intended.

I have an Enya .35, and eventually want to get a hold of an RC .09

microflitedude wrote:

happydad wrote:

microflitedude wrote:Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude: is that just your favorite quote or are you interested in enya engines as well? quiet, so no one hears us talk. LOL

happydad

Pun intended.

I have an Enya .35, and eventually want to get a hold of an RC .09

microflitedude: the reason i asked is that i am looking for a home for an enya .19 RC water cooled Marine engine i sent my dad in 1967 when i was in Japan in the USAF. he started to build a 30inch balsa boat, (far too small for a .19 engine), but never finished it. flash forward i take posession of the boat a few years ago and the boat balsa is soft and starting to fall apart and the engine mounts soggy from soft balsa not fuel. my dad had never really broke in the engine. i realized that the boat needed an 05 electric motor and started rebuilding the structure and glassing the bottom of the boat with 0.5ounce glass to keep the weight down. anyway to make a long story short i tried to sell the enya .19 RC marine WC engine on ebay and wasn't offered a bid at any price so i held onto it until now. like i said i'm looking for a good home. some one who appreciates enya engines.

happydad p.s. very low mileage. everything is clean and working. pics on request.

happydad wrote:

microflitedude wrote:

happydad wrote:

microflitedude wrote:Doug, I received my engines today. All they need is two short needles and a little TLC.

Thanks again.

microflitedude: is that just your favorite quote or are you interested in enya engines as well? quiet, so no one hears us talk. LOL

happydad

Pun intended.

I have an Enya .35, and eventually want to get a hold of an RC .09

microflitedude: the reason i asked is that i am looking for a home for an enya .19 RC water cooled Marine engine i sent my dad in 1967 when i was in Japan in the USAF. he started to build a 30inch balsa boat, (far too small for a .19 engine), but never finished it. flash forward i take posession of the boat a few years ago and the boat balsa is soft and starting to fall apart and the engine mounts soggy from soft balsa not fuel. my dad had never really broke in the engine. i realized that the boat needed an 05 electric motor and started rebuilding the structure and glassing the bottom of the boat with 0.5ounce glass to keep the weight down. anyway to make a long story short i tried to sell the enya .19 RC marine WC engine on ebay and wasn't offered a bid at any price so i held onto it until now. like i said i'm looking for a good home. some one who appreciates enya engines.

happydad p.s. very low mileage. everything is clean and working. pics on request.

if MFD does not want it, It would make a great addition to my collection

thanks, my engines arrived today and they both are in running condition now except i also need the needle valves for them and a new glow plug because one of them is burnt out
Thanks, loving the engines

if MFD does not want it, It would make a great addition to my collection [/quote]

mitchg95: i'll keep that in mind. i just took pics of the hustler 10 to post or PM those interested and as soon as i get a chance i'll do the same for the enya .19 RC WC marine. busy busy. happydad

i aslo like enyas...tho i only have a 0.49 rc enya it needs a new piston n liner



i would be interested in a few of those parts engines as well

plz included postage to australia ?

Hi Thomas I got your box off to Denmark, photo of customs form and shipping cost

Hi Doug,
Thank you very much!!
I have just written you a PM, but i can see that everything is just fine!
Money sent too.

Regards
Thomas Pedersen

so why cant one mount a prop on these engines?? i did i use this engine in a opusher configeration on my fantrainer

Whittled the 99 down quite a bit, maybe I need another 99.

crankbndr wrote:Whittled the 99 down quite a bit, maybe I need another 99.

crankbndr: i think the seller is down on supply. i made a reasonable offer on car engines and he refused saying his supply is limited now.
and p.s. jason is working on a prop drive plate for both the tapered shaft and the splined shaft car engine crankshafts.
happydad

Happydad, he is running low because EX got 1000. WOWeeeeee

http://www.ebay.com/itm/330746010542#ht_500wt_1182

Yes, we bought a large quantity of these engines along with some other parts. I have begun the process of sorting through them. They consist of new, test run (possibly from old R&D?), and well used. Most are locked up.

They were not bought to be car engines as they are. The idea is to use the new parts around designing a couple of new engines, as well as offering them as spares depending upon quantity. I hope to have driveplates made for the car crankcases since they do not serve much use the way they are currently configured.

The used engines will be cleaned and offered for sale as refurbished engines and parts.

Regards, Matt

crankbndr wrote:Happydad, he is running low because EX got 1000. WOWeeeeee

http://www.ebay.com/itm/330746010542#ht_500wt_1182

wow, thats awesome didnt know it was possible to get that many

Breaking down that many will be a job and a half, they are a bear to get apart.
I have many hours in the 99 i got. Hope you make the drive plates I need a bunch.